The Effect of Milling Time and Sintering Temperature on the Microstructure and Mechanical Properties of Al/20% SiC Composite Prepared by Powder Metallurgy

Document Type : Research Paper

Authors

• N Talavari
• Kh Gheisari
• M Reihanian

Abstract

Metal matrix composites (MMCs) are considered for their mechanical properties and wear resistance. In this study, the effect of milling time and sintering temperature on the microstructure and mechanical properties of Al/SiC composites was studied. Firstly, the powders with volume fraction of Al/20% SiC were mixed in a planetary ball mill under argon atmosphere for milling time of 0.5, 1, 2, 4 and 8 h. Then, the mixed powders were pressed by a cold pressure of 500 MPa into pellets and rods. With regard to the microstructure properties of the samples, the optimized milling time was determined. Then, the pressed samples were capsulated and sintered for 1 h at 400, 450, 500, 550 and 600 ⁰C. Morphology, mechanical and tribological properties of the prepared composites was evaluated by scanning electron microscope (SEM), hardness and wear test. The result showed that the optimized milling time and sintering temperature are 8 h and 600 ⁰C, respectively. Also, density, hardness and wear resistance increase with increasing sintering temperature.

Keywords

• Mechanical milling
• Milling time
• Sintering temperature
• Wear Resistance, Al/SiC Composites

---

References

1- K. K. Chawla, “ Metal Matrix Composie” , Springer , New York, USA , 2006 .

2- J.M. Torralba, C.E. da Costa, and F. Velasco, “P/M Aluminum Matrix Ccomposites: an Overview”, Journal of Materials Processing Technology, Vol. 133, 2003, pp. 203–206.

3- M.K. Surappa, " Aluminum Matrix Composite: Challenges and Opportunities ", Sadhana, Vol. 28, 2003 , pp. 319-334.

4- ن. نصیریان و خ. رنجبر، " بررسی خواص مکانیکی و ریزساختاری کامپوزیت  Al/Brassساخته شده به روش اتصال نوردی تجمعی"، مجله مواد نوین، جلد 3، شماره 1، صص45-54، پاییز 1391.

5- ح. شریفی، م. حیدری، م. دیواندری، ع. خاوندی، " بررسی رفتار سایش خشک کامپوزیت های               ZrO / Mg-Al تهیه شده به روش نفوذدهی بدون فشار"، مجله مواد نوین،جلد3 شماره 4، صص 13-26، تابستان 1392.

6- ع. عبدالهی، ع. علیزاده، "تولید نانوکامپوزیت دوجزئی فوق مستحکم زمینه آلومینیومی به روش آلیاژسازی مکانیکی و اکستروژن داغ و بررسی خواص مکانیکی آن"، مجله مواد نوین، جلد 4 ، شماره 1، صص 83-95، پاییز 1392.

7- T. Imai, J.F. Mao, Sh. Dong, I. Shigematsu, N. Saito, and G. Esperance, " High Strain Rate Superplasticity of TiC Particulate Reinforced 2014 Aluminum Alloy Composites", Materials Science and Engineering: A, Vol. 364, pp. 281–286. 2004.

8- Z. Sadeghian, B. Lotfi, M.H. Enayati, and P. Beiss, “Microstructural and Mechanical Evaluation of Al–TiB₂ Nanostructured Composite Fabricated by Mechanical Alloying”, Journal of Alloys and Compounds, Vol. 509 , pp. 7758– 7763. 2011.

9- C. Hofmeister, B. Yao, Y. H. Sohn, T. Delahanty, M. Van den Bergh, and K. Cho, "Composition and Structure of Nitrogen-Containing Dispersoids in Trimodal Aluminum Metal–Matrix Composites", Journal of Materials Science, Vol.45 , pp. 4871–4876. 2010.

10- B. Xionga, , Zh. Xua, Q. Yana, C. Caia, Y. Zhenga, and B. Lub, "Fabrication of SiC Nanoparticulates Reinforced Al Matrix Composites by Combining Pressureless Infiltration with Ball-Milling and Cold-Pressing Technology", Journal of Alloys and Compounds, Vol. 497, pp.L1–L4. 2010.

11- S.J. Hong, P.W. Kao, and C.P. Chang, " Microstructural Development in Al_SiC Composites Made by Resistance Sintering of Mechanically Alloyed Powder", Material Science and Engineering A, Vol. 158, pp.195-202. 1992.

12- C.S. Shin, and J.C. Huang, "Effect of Temper, Specimen Orientation and Test Temperature on the Tensile and Fatigue Properties of SiC Particles Reinforced PM 6061 Al Alloy", International Journal of Fatigue, Vol. 32, pp. 1573–1581. 2010.

13- S.C. Tjong, and Z.Y. Ma, "High-Temperature Creep Behaviour of Powder-Metallurgy Aluminium Composites Reinforced with SiC Particles of Various Sizes", Composites Science and Technology, Vol. 59, pp. 1117-1125. 1999.

14- Z.Z. Chena, and K. Tokaji, "Effects of Particle Size on Fatigue Crack Initiation and Small Crack Growth in SiC Particulate-Reinforced Aluminium Alloy Composites", Materials Letters, Vol. 58, pp. 2314– 2321. 2004.

15- T.S. Srivatsan, and R. Auradkar, "Effect of Silicon Carbide Particulateon Cyclic Plastic Strain Response Characteristics and Fracture of Aluminiurn Alloy Composites", International Journal of Fatigue, Vol. 14, pp. 355-366. 1992.

16- S.M.R. Mousavi Abarghouie, and S.M. Seyed Reihani, "Aging Behavior of a 2024 Al Alloy-SiCp Composite", Materials and Design, Vol. 31, pp. 2368–2374. 2010.

17- Y. Sahin, "Abrasive Wear Behavior of SiC/2014 Aluminium Composite", Tribology International, Vol. 43, pp. 939–943. 2010.

18- C. Suryanarayana, "Mechanical Alloying and Milling", Progress in Materials Science, Vol. 46, pp. 1-184. 2001.

19- B.D. Culity, "Elements of X-ray Diffraction", 2 ed, Addison Wesley Publishing Company, Massachusetts, 1978.

20- R.M. German, "Sintering Theory and Practice", New York, Wiley, 1996.

21- DA. Porter, and KE. Easterling, "Phase Transformations in Metals and Alloys", McGraw-Hill, 1980.

22- M. Rahimian , N. Parvin , and N. Ehsani. "The Effect of Production Parameters on Microstructure and Wear Resistance of Powder Metallurgy Al–Al2O3 Composite", Materials and Design, Vol. 32, p.p. 1031–1038. 2011.

23- H. Arik, "Effect of Mechanical Alloying Process on Mechanical Properties of a-Si3N4 Reinforced Aluminum-Based Composite Materials", Materials and Design, Vol. 29, p.p. 1856–1861. 2008.

24- H. Abdizadeh, M. Ashuri, P. Tavakoli Moghadam, A. Nouribahadory, and H.R. Baharvandi, "Improvement in Physical and Mechanical Properties of Aluminum/Zircon Composites Fabricated by Powder Metallurgy Method",  Materials and Design, Vol. 32, p.p. 4417–4423. 2011.

25- J.F. Archard, "Contact and Rubbing of Flat Surface", Journal of Applied Physics, Vol. 24, pp.981–988. 1953.