Investigating the effect of particle size on microstructure, mechanical properties and electrical conductivity of sodium beta-alumina ceramics

Document Type : Research Paper

Authors

• Hajar Ahmadimoghadam ¹
• Mohammad Hossein Paydar ²

¹ Department of Material Engineering, Faculty of Engineering, Shahrekord University, Shahrekord

² Department of Materials Science and Engineering, School of Engineering, Shiraz University, Shiraz

Abstract

The microstructure control of sodium beta-alumina electrolyte used in the manufacture of sodium sulfur batteries is important for obtaining appropriate mechanical and ionic conductivity properties. In this research, the effect of particle size of sodium beta-alumina powder on the final microstructure and properties of this ceramic has been investigated. For this purpose, solid-state-synthesized sodium beta-alumina powder was milled by attrition milling for 30 min, 2, 6, and 10 hours. The results showed that the milling time had a significant effect on the powder particle size and consequently on the condensation behavior, microstructure, and finally on the fracture strength and ionic conductivity of sodium beta-alumina electrolyte. By increasing the milling time from 30 minutes to 6 hours and reducing the average particle size of the powder from about 2 to 0.7 microns, the resulting powder condensation behavior improved due to increased sintering diving force, resulting in increased fracture strength and ionic conductivity of up to 65% and 100%, at high temperatures. With increasing the milling time to 10 hours, due to the development of non-uniform microstructure, a decrease in the mechanical and electrical properties of sodium beta-alumina ceramic was observed. The results of this study also showed a linear relationship between the fracture strength and the density of the samples can be established.

Keywords

• Sodium beta-alumina
• Milling time
• Microstructure
• Strength
• ionic conductivity

20.1001.1.22285946.1398.9.36.8.2

---

References

References:

 

[1] G. Y. Onoda and  L. L. Hench, Ceramic Processing Before Firing, Wiley, New York, 1978.   

[2] M. Barsoum and M.W. Barsoum, Fundamentals of Ceramics, CRC press, 2002.

[3] M. N. Rahaman, Ceramic Processing and Sintering, Marcel Dekker, New York, 1995.

[4] S.S. Razavi-Tousi and J. A. Szpunar, "Effect of ball size on steady state of aluminum powder and ef fi ciency of impacts during milling", Powder technology, vol. 284, pp. 149–158, 2015.

[5] S. Maleki and A. Karimi-jashni, "Effect of ball milling process on the structure of local clay and its adsorption performance for Ni (II) removal", Applied Clay Science, vol. 137, pp. 213–224, 2017.                  

[6] P. Kuziora, M. Wyszyńska, M. Polanski and J. Bystrzycki, "Why the ball to powder ratio (BPR) is insufficient for describing the mechanical ball milling process", Journal of Hydrogen Energy, Vol. 39, pp. 9883-9887, 2014. 

[7] X. Lu, G. Xia, J. P. Lemmon, and Z. Yang, "Advanced materials for sodium-beta alumina batteries : Status , challenges and perspectives", Journal of Power Sources, vol. 195, pp. 2431–2442, 2010.

 

[8] Z. Wen, Z. Gu, X. Xu, J. Cao, F. Zhang, and Z. Lin, "Research activities in Shanghai Institute of Ceramics, Chinese Academy of Sciences on the solid electrolytes for sodium sulfur batteries", Journal of Power Sources, vol. 184, pp. 641–645, 2008.        

[9] C. Zhu, J. Xue, and G. Ji, "Effect of Na₂O content on properties of beta alumina solid electrolytes," Materials Science in Semiconductor Processing, vol. 31, pp. 487–492, 2015.  

[10] H. Ahmadi Moghammad, and M. H. Paydar, "Investigation of Sm₂O₃ additive on mechanical and electrical properties of Li₂O- stabilized β ″ -alumina electrolyte", Journal of Applied Ceramic Technology, vol. 14, pp. 1183–1189, 2017.    

[11] T. Oshima, M. Kajita, and A. Okuno, "Development of Sodium-Sulfur Batteries", Journal of Applied Ceramic Technology, vol. 1, pp. 269–276, 2004.

[12] L. Yang, S. Shan, X. Wei, X. Liu, H. Yang, and X. Shen, "The mechanical and electrical properties of ZrO₂–TiO₂–Na-β/β″-alumina composite electrolyte synthesized via a citrate sol–gel method", Ceramics International, vol. 40, pp. 9055–9060, 2014.      

]13[.ه. احمدی مقدم و م. ح. پایدار،"بررسی سنتز و رفتار چگالشβ″-آلومینا به عنوان الکترولیت باتری‌های سدیم سولفور"، مجله مواد نوین، دوره 6، شماره 22، ص 146-137،زمستان 1394.       

[14] H. Ahmadi Moghadam and M. H. Paydar, "The effect of nno CuO as sintering aid on phase formation , microstructure and properties of Li₂O-stabilized β″-alumina ceramics", Journal of Ceramic Science and Technolog, vol. 7, pp. 441–446, 2016.     

[15] D. Xu, H. Jiang, M. Li, O. Hai, and Y. Zhang, "Synthesis and characterization of Y₂O₃ doped Na–β″-Al₂O₃ solid electrolyte by double zeta process", Ceramics International, Vol. 41, pp. 5355-5361, 2015.

[16] C.L. Dirksen, K. Skadell, M. Schulz and M. Stelter, "Effects of TiO₂ doping on Li⁺-stabilized Na-β″-alumina for energy storage applications", Separation and Purification Technology, Vol. 213, pp. 88-92, 2019.