Production of Aluminum metal matrix composite reinforced with Al-Cr-Fe quasicrystal nano-powder by using accumulative roll bonding process and investigation mechanical properties

Document Type : Research Paper

Authors

• Shima Pashangeh ¹
• Morteza Alizadeh ²
• Rasool Amini ²

¹ Ph.D. in Material Engineering, Department of Science and Engineering, Shiraz University of Technology, Shiraz, Iran

² Associate Prof. of Material Engineering, Department of Science and Engineering, Shiraz University of Technology, Shiraz, Iran

10.30495/jnm.2021.28185.1922

Keywords

• Accumulative roll bonding process
• Severe plastic deformation
• Quasicrystal nano-particles
• Aluminum matrix composite
• Mechanical properties

20.1001.1.22285946.1400.12.44.3.0

---

References

         Cheng, S.-L. Yang, G.-C., Man, Z.H.U., Wang, J.-C., Zhou,Y.Z. 2010. Mechanical properties and fracture mechanisms of aluminum matrix composites reinforced by Al9 (Co, Ni) 2 intermetallics. Transactions of Nonferrous Metals Society of China, 20: 572–576.

2.    Balokhonov, R., Romanova, V., and Kulkov, A. 2020. Microstructure-based analysis of deformation and fracture in metal-matrix composite materials. Engineering Failure Analysis, 110: 104412.

3.    Kumar, A., Yeasin Arafath, M., Gupta, P., Kumar, D., Mustansar Hussain, C., and Jamwal, A. 2020, Microstructural and mechano-tribological behavior of Al reinforced SiC-TiC hybrid metal matrix composite. Materials Today: Proceedings, 21: 1417–1420.

4. Alizadeh, M., and Paydar, M.H. 2009. Fabrication of Al/SiCP composite strips by repeated roll-bonding (RRB) process. Journal of Alloys and Compounds, 477: 811–816.

5. Tang, F., Anderson, I.E., and Biner, S.B. 2003. Microstructures and mechanical properties of pure Al matrix composites reinforced by Al; Cu; Fe alloy particles. Materials Science and Engineering: A, 363: 20–29.

6.    Alizadeh, M., Ghaffari, M., and Amini, R. 2013. Properties of high specific strength Al-4 wt.% Al2O3/B4C nano-composite produced by accumulative roll bonding process. Materials & Design, 50: 427–432.

7.    Behroozi, D. and Pirhady Tavandashti, N. 2021. Investigation of the Synergistic Effect of Soft and Hard Particles on Corrosion and Wear Resistance Behavior of Ni-B-PTFE-Si3N4 Electroless Coating on Carbon Steel. Journal of New Materials, 11: 1–22. [in Persian]

8.    Manikandan, M., and Karthikeyan, A. 2014. A study on the wear behaviour of Aluminium matrix composite with ceramic reinforcements. Middle East Journal of Scientific Research, 22: 128–133.

9.    Giacometti, E., Baluc, N., Bonneville, J., and Rabier, J. 1999. Microindentation of Al-Cu-Fe icosahedral quasicrystal. Scripta Materialia, 41.

10.  Yan, M., Wang, J.Q., Kong, C., Schaffer, G.B., and Qian, M. 2012. Micrometer-sized quasicrystals in the Al 85 Ni 5 Y 6 Co 2 Fe 2 metallic glass: a TEM study and a brief discussion on the formability of quasicrystals in bulk and marginal glass-forming alloys. Journal of Materials Research, 27: 2131–2139.

11.  Lee, S.M. Jung, J.H., Fleury, E., Kim, W.T., and Kim, D.H. 2000. Metal matrix composites reinforced by gas-atomised Al-Cu-Fe powders. Materials Science and Engineering: A, 294: 99–103.

12.  Huttunen-Saarivirta, E. 2004. Microstructure, fabrication and properties of quasicrystalline Al-Cu-Fe alloys: a review,  Journal of Alloys and Compounds, 363: 154–178.

13.  Kaloshkin, S.D., Tcherdyntsev, V. V, Laptev, A.I., Stepashkin, A.A., Afonina, E.A., Pomadchik, A.L., and Bugakov, V.I.  2004. Structure and mechanical properties of mechanically alloyed Al/Al-Cu-Fe composites. Journal of materials science, 39: 5399–5402.

14.  Cherdyntsev, V. V.,  Kaloshkin, S.D., Tomilin, I.A., Shelekhov, E. V.,  Laptev, A.I., Stepashkin, A.A., and Danilov, V.D. 2007. Structure and properties of mechanically alloyed composite materials Al/Al-Cu-Fe quasicrystal. The Physics of Metals and Metallography, 104: 497–504.

15.  Alizadeh, M. 2010. Comparison of nanostructured Al/B4C composite produced by ARB and Al/B4C composite produced by RRB process. Materials Science and Engineering: A, 528: 578–582.

16.  Dieter, G.E., and Bacon, D.J. 1986. Mechanical metallurgy. McGraw-hill New York, 3.

17.  Tsuji, N., Ito, Y., Saito, Y., and Minamino, Y. 2002. Strength and ductility of ultrafine grained aluminum and iron produced by ARB and annealing. Scripta Materialia, 47: 893–899.

18.  Alizadeh, M., and Paydar, M.H. 2012. High-strength nanostructured Al/B4C composite processed by cross-roll accumulative roll bonding, Materials Science and Engineering: A, 538: 14–19.

19.  Kolmogorov, V.L., and Zalazinsky, A.G. 1998. On metal joining and the prediction of the strength of solid-phase joints. Journal of Materials Processing Technology, 75: 157–164.

20.  Saito, Y., Utsunomiya, H., Tsuji, N., and Sakai, T. 1999. Novel ultra-high straining process for bulk material_development of the accumulative roll-bonding (ARB) process. Acta Materialia, 47: 579–583.

21.  Zhan, M.Y., Li, Y.Y., Chen, W.P., and Chen, W.D. 2007. Microstructure and mechanical properties of Mg–Al–Zn alloy sheets severely deformed by accumulative roll-bonding. Journal of Materials Science, 42: 9256–9261.

22.          Park, K.-T. Kwon, H.-J., Kim, W.-J., and Kim, Y.-S. 2001. Microstructural characteristics and thermal stability of ultrafine grained 6061 Al alloy fabricated by accumulative roll bonding process. Materials Science and Engineering: A, 316: 145–152