Tensile behavior of AZ91 alloy containing silver and under different casting conditions

Document Type : Article frome a thesis

Authors

• Pouria Kamaei ¹
• Mehdi Khorasanian ²
• Seyed Reza Alavi Zaree ³
• Mostafa Eskandari ²

¹ MSc graduated of Materials Science and Engineering, Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran

² Assistant prof. of Materials Science and Engineering, Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran

³ Associate prof. of Materials Science and Engineering, Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran

10.30495/jnm.2023.32303.2009

Abstract

Abstract
The aim of the present research was to study the behavior of AZ91 magnesium alloy under cold and hot tension tests. The alloy was cast under solidification conditions with and without a chill. During the preparation of the melt, silver was added in different amounts to the melt. The uniaxial tensile test was performed at room temperature and at 120 °C on the samples with different percentages of silver and with different solidification conditions. The results showed that the presence of silver in the alloy caused a change in the morphology of the Mg17Al12 phase and a change in the microstructure and tensile properties of the alloy. The change in the morphology of this phase has a significant effect on the mechanical properties of the alloy. This phase is a brittle phase, and along with the hexagonal crystal structure of magnesium, can deteriorate the tensile behavior of the alloy. The best tensile behavior was obtained for the sample with 0.1 wt% silver without a chill. In this sample, the Mg₁₇Al₁₂ phase appeared as a dispersed phase with less continuity at the grain boundaries. When the amount of silver increased to 0.4 wt%, the tensile properties decreased significantly due to the increase of the size of this phase in the microstructure. solidification with a chill had no positive effect on the tensile properties of the alloy at high and low temperatures.
Introduction:The aim of the present research was to study the behavior of AZ91 magnesium alloy under cold and hot tension tests. The alloy was cast under solidification conditions with and without a chill. During the preparation of the melt, silver was added in different amounts to the melt.  Methods: AZ91 specimens were produced using permanent mold casting. The raw materials were heated in the form of commercial ingots in an electric furnace, and after melting, silver was introduced into the melt in the form of commercial pure granules.
Findings:
In Figure 3, the results of room temperature tensile tests on samples containing 0.1 wt% of silver and with different solidification conditions namely sample 1 (casting without chill at 650 ˚C), sample 2 (casting with chill at 750 ˚C) and Sample 3 (casting with chill at 850 ˚C) is shown.

Keywords

• AZ91 magnesium alloy
• Casting
• Chilled solidification
• Microstructure
• Tension test

20.1001.1.22285946.1401.13.50.5.1

---

References

[1].       Unal M, Ahmet Goren H, Koc E, Turen Y, Ahlatci H, Sun Y. Effect of cooling rate and 2 Wt % silicon addition on microstructure and mechanical properties of Az91 Mg alloys. Int J Mech Prod Eng [Internet]. 2017;(5):2320–2092.

[2].       Mabuchi M, Kobata M, Chino Y, Iwasaki H. Tensile properties of directionally solidified AZ91 Mg alloy. Mater Trans. 2003;44(4):436–9. DOI: 10.2320/matertrans.44.436.

[3].       Srinivasan A, Pillai UTS, Pai BC. Microstructure and mechanical properties of Si and Sb added AZ91 magnesium alloy. Metall Mater Trans A Phys Metall Mater Sci. 2005;36(8):2235–43. DOI: 10.1007/s11661-005-0342-6.

[4].       Muraliraja R, Vettrivel H, Elansezhian R. Synthesis and characterization of magnesium alloy added with Yttrium and to study the microstructure and mechanical properties. Int J Eng Innov Technol. 2013;2(7):388–92. DOI: 10.2320/matertrans.44.436.

[5].       Wang SR, Guo PQ, Yang LY, Wang Y. Microstructure and mechanical properties of AZ91 alloys by addition of Yttrium. J Mater Eng Perform. 2009;18(2):137–44. DOI: 10.1007/s11665-008-9255-z.

[6].       Suresh M, Srinivasan A, Ravi KR, Pillai UTS, Pai BC. Influence of boron addition on the grain refinement and mechanical properties of AZ91 Mg alloy. Mater Sci Eng A. 2009;525(1–2):207–10. DOI: 10.1016/j.msea.2009.07.019.

[7].       Srinivasan A, Swaminathan J, Pillai UTS, Guguloth K, Pai BC. Effect of combined addition of Si and Sb on the microstructure and creep properties of AZ91 magnesium alloy. Mater Sci Eng A. 2008;485:86–91. DOI: 10.1016/j.msea.2007.09.059.

[8].       Kumar P, Mondal AK, Chowdhury SG, Krishna G, Ray AK. Influence of additions of Sb and/or Sr on microstructure and tensile creep behaviour of squeeze-cast AZ91D Mg alloy. Mater Sci Eng A [Internet]. 2017;683(2016):37–45. DOI: 10.1016/j.msea.2016.12.006.

[9].       Chen SN, Yang W, Yu H, Zhang YL, Yang W, Yu H, et al. Effects of microstructure modification and pressurized solidification on mechanical property of AZ91 alloy. J Alloys Compd. 2014;611:1–6. DOI: 10.1016/j.jallcom.2014.05.033.

[10].     Wang ZW, Wang HX, Gong JL, Li M, Cheng WL, Liang W. Modification and refinement effects of Sb and Sr on Mg17Al12 and Mg2Si phases in Mg-12Al-0.7Si alloy. China Foundry. 2016;13(5):310–5. DOI: 10.1007/s41230-016-5112-0.

[11].     Wei W, Chunxiang X, Jinshan Z, Weili C, Xiaofeng N. Effects of Ce addition on microstructure , mechanical properties and corrosion resistance of as-cast AZ80 magnesium alloy. China Foundry. 2014;11(3):157–62.

[12].     Gusieva K, Sato T, Sha G, Ringer SP, Birbilis N. Influence of low level Ag additions on Mg-alloy AZ91. Adv Eng Mater. 2013;15(6):485–90. DOI: 10.1002/adem.201200321.

[13].     Bian J, Yu B, Sun W, Jiang L, Liu X, Zheng L, et al. Improving the microstructure and tensile properties of AZ91 magnesium alloy via electromagnetic stirring Improving the microstructure and tensile properties of AZ91 magnesium alloy via electromagnetic stirring. Mater Res Express. 2019;6(12):1–10. DOI: 10.1088/2053-1591/ab7219.

[14].     Askaran M, Malekan M, Emamy M, Lotfpour M. Grain refinement , microstructural characterization , and tensile properties of die-cast AZ91 alloy via lead and tin additions. J Ultrafine Grained Nanostructured Mater. 2019;52(2):218–28. DOI: 10.22059/jufgnsm.2019.02.11.

[15]. عسکران م ر، امامی م، ملکان م. بررسی تاثیر سرب بر ریز ساختار و خواص مکانیکی آلیاژ منیزیم AZ91. مجله مواد نوین. 1397;9(1):25–36.

[16].     Afsharnaderi A, Malekan M, Emamy M, Ghani JR, Lotfpour M. Microstructure evolution and mechanical properties of the AZ91 magnesium alloy with Sr and Ti additions in the as-cast and as-aged conditions. J Mater Eng Perform [Internet]. 2019;28(11):6853–63. DOI: 10.1007/s11665-019-04396-2.

[17].     افشار نادری آ، راثی‌زاده غنی ج، ملکان م، امامی م. بررسی تاثیر استرانسیم بر ریزساختار و خواص مکانیکی آلیاژ منیزیم AZ91. مجله مواد نوین. 1397;8(4):31–42.

[18].     Bonnah RC, Fu Y, Hao H. Microstructure and mechanical properties of AZ91 magnesium alloy with minor additions of Sm , Si and Ca elements. China Foundry. 2019;16(5):319–25. DOI: 10.1007/s41230-019-9067-9.

[19].     Afsharnaderi A, Lotfpour M, Mirzadeh H, Emamy M, Malekan M. Enhanced mechanical properties of as-cast AZ91 magnesium alloy by combined RE-Sr addition and hot extrusion. Mater Sci Eng A [Internet]. 2020;792. DOI: 10.1016/j.msea.2020.139817.

[20].     Marodkar AS, Patil H, Borkar H. Microstructure , mechanical properties and fretting wear behavior of gravity die cast and squeeze cast AZ91 Mg alloy. Metallogr Microstruct Anal [Internet]. 2023;12(4):702–13. DOI: 10.1007/s13632-023-00974-y.

[21].     Marodkar AS, Patil H, Borkar H. Effect of squeeze casting and combined addition of calcium and strontium on microstructure and mechanical properties of AZ91 magnesium alloy. Int J Met. 2023;17:2252–2270. DOI: 10.1007/s13632-023-00974-y.

[22].     Khorasanian M, Zaree SRA, Kamaei P, Eskandari M. Addition of silver to an Mg–Al–Zn alloy treated by conventional and chilled solidification: A microstructural approach. Phys Met Metallogr. 2020;121(14):1393–9. DOI: 10.1134/S0031918X20130074.

[23].     Khorasanian M, Yeganeh M, Gholamzadeh N, Alavi Zaree SR. Effect of addition of silver and chilled casting on corrosion behavior of AZ91 magnesium alloy. Int J Met [Internet]. 2021;15:1184–96. DOI: 10.1007/s40962-020-00558-4.

[24].     Chen Y, Feng Y, Wang L, Wang L, Jia G, Guo E. Effect of cooling rate and Al content on solidification behavior and microstructure evolution of as-cast Mg – Al – Ca – Sm alloys. J Therm Anal Calorim [Internet]. 2019;135:2237–46. DOI: 10.1007/s10973-018-7434-1.

[25].     Maldar AR, Ebrahimi R, Davoodi A. The effect of homogenization on microstructure and hot ductility behaviour of AZ91 magnesium alloy. Kov Mater. 2010;48(5):277–84. DOI: 10.4149/km_2010_5_277.

[26].     Fu P, Peng L, Jiang H, Ding W, Zhai C. Tensile properties of high strength cast Mg alloys at room temperature: A review. China Foundry. 2014;11(4):277–86. 
 
[27].     Fu L, Wang XB, Gou PL, Le QC, Jia WT, Tang Y. Microstructures and tensile properties of AZ91 magnesium alloys with Ca, Sm, and La elements additions. Adv Eng Mater. 2017;19(12):1–9. DOI: 10.1002/adem.201700230.

[28].     Zhu S, Easton MA, Abbott TB, Nie JF, Dargusch MS, Hort N, et al. Evaluation of magnesium die-casting alloys for elevated temperature applications: microstructure, tensile properties, and creep resistance. Metall Mater Trans A Phys Metall Mater Sci. 2015;46(8):3543–54. DOI: 10.1007/s11661-015-2946-9.